ASTM C335/C335M-10e1 Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

ASTM C335/C335M-10e1 管道绝热材料稳态热传递特性试验方法

1. ASTM C335/C335M标准适用范围

1.1 This test method covers the measurement of the steady-state heat transfer properties of pipe insulations. Specimen types include rigid, flexible, and loose fill; homogeneous and nonhomogeneous; isotropic and nonisotropic; circular or non-circular cross section. Measurement of metallic reflective insulation and mass insulations with metal jackets or other elements of high axial conductance is included; however, additional precautions must be taken and specified special procedures must be followed.

1.2 The test apparatus for this purpose is a guarded-end or calibrated-end pipe apparatus. The guarded-end apparatus is a primary (or absolute) method. The guarded-end method is comparable, but not identical to ISO 8497.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 When appropriate, or as required by specifications or other test methods, the following thermal transfer properties for the specimen can be calculated from the measured data (see 3.2):

1.4.1 The pipe insulation lineal thermal resistance and conductance,

1.4.2 The pipe insulation lineal thermal transference,

1.4.3 The surface areal resistance and heat transfer coefficient,

1.4.4 The thermal resistivity and conductivity,

1.4.5 The areal thermal resistance and conductance, and

1.4.6 The areal thermal transference.

Note 1—In this test method the preferred resistance, conductance, and transference are the lineal values computed for a unit length of pipe. These must not be confused with the corresponding areal properties computed on a unit area basis which are more applicable to flat slab geometry. If these areal properties are computed, the area used in their computation must be reported.

2. ASTM C335/C335M参考标准

ISO 8497 Thermal Insulation-Dermination of Steady State Thermal Transmission Properties of Thermal Insulation for Circular Pipes

ASTM C168 Terminology Relating to Thermal Insulation

ASTM C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

ASTM C302 Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation

ASTM C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

ASTM C680 Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs

ASTM C870 Practice for Conditioning of Thermal Insulating Materials

ASTM C1045 Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions

ASTM C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation

ASTM E230 Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples

我们同时还提供英国BS6853、德国DIN5510、欧盟EN45545、法国NFF16-101/NFF16-102、美标NFPA130、意大利SINAL资质的测试，新加坡SAC-SINGLAS认证等

英国BS6853测试    http://www.firete.com/fire_standard/railway/163.html

德国DIN5510-2测试   http://www.firete.com/fire_standard/railway/535.html

法国NFF16-101测试http://www.firete.com/fire_standard/railway/164.html

美国NFPA130测试        http://www.firete.com/fire_standard/railway/166.html

EN 45545-2-2013欧盟最新标准http://www.firete.com/fire_standard/railway/167.html

中国防火网全国免费咨询电话：400-666-7290 025-8658 3475

网址：www.firete.com

邮箱：info@firete.com

...